File must contain one line, example: R3300000,R3400000,NC430000,...

Additional configuration for the WirePlumber daemon when run in single-instance mode (the default in nixpkgs and currently the only supported way to run WirePlumber configured via extraConfig)

Install the devicetree blob specified by config.hardware.deviceTree.name to the ESP and instruct systemd-boot to pass this DTB to linux.

Priority of the zram swap devices

Maximum total amount of memory (in bytes) that can be stored in the zram swap devices

This is where you configure all the UPSes that this system will be monitoring directly

Structural setting for the rshim configuration file (/etc/rshim.conf)

Maximum total amount of memory that can be stored in the zram swap devices (as a percentage of your total memory)

Enable in-memory compressed devices and swap space provided by the zram kernel module

Whether to delete the devices which are not configured via the devices option

Whether to delete the devices which are not configured via the devices option

Whether to enable support for Power Devices, such as Uninterruptible Power Supplies, Power Distribution Units and Solar Controllers .

Number of zram devices to be used as swap, recommended is 1.

Whenever smartd should monitor all devices connected to the machine at the time it's being started (the default)

Grant access to i2c devices (/dev/i2c-*) to users in this group.

Mode to set for devices of the msr kernel subsystem.

Owner to set for devices of the msr kernel subsystem.

Group to set for devices of the msr kernel subsystem.

Whether the Clevis JWE file used to decrypt the devices uses a Tang server as a pin.

Enables support for authenticating with FIDO2 devices.

Whether to enable udev rules for Ledger devices.

Use ping to check online status of devices instead of mDNS

Definition of systemd network devices.

Whether to enable i2c devices support

Whether to enable udev rules for devices supported by libftdi.

Enables udev rules for BladeRF devices

Whether to enable Hard Drive Active Protection System Daemon, devices are detected and managed automatically by udev and systemd .

Whether to enable udev rules for Saleae Logic devices.

Whether to enable pmount, a tool that allows normal users to mount removable devices without requiring root privileges .

Whether to make the /dev/tpm[0-9] devices accessible by the tssUser, or the /dev/tpmrm[0-9] by tssGroup respectively

Whether to enable the msr (Model-Specific Registers) kernel module and configure udev rules for its devices (usually /dev/cpu/*/msr).

Whether to enable udisks2, a DBus service that allows applications to query and manipulate storage devices.

Files or block devices to make available over the network.

Whether to restart the computer after a power failure

Enables udev rules for Nitrokey devices.

Mirror the boot configuration to multiple partitions and install grub to the respective devices corresponding to those partitions.

Whether to enable Novacom service for connecting to WebOS devices.

Number of /dev/fanout devices

This option allows you to define vlan devices that tag packets on top of a physical interface

Whether to apply security hardening measures to wpa_supplicant

Enable this option to support IIO sensors with iio-sensor-proxy

Whether to enable support for Logitech LCD Devices.

Configuration for devices that aren't hotpluggable

This option allows you to define bond devices that aggregate multiple, underlying networking interfaces together

Enables rtl-sdr udev rules, ensures 'plugdev' group exists, and blacklists DVB kernel modules

Controls how to operate on empty devices that contain no partition table yet

Whether to open the firewall for UDP port 5353

Whether to enable spacenavd to support 3DConnexion devices.

The list of network devices that will be registered against the brscan4 sane backend.

The list of network devices that will be registered against the brscan5 sane backend.

Definition of systemd network devices.

Enables hackrf udev rules and ensures 'plugdev' group exists

Whether to automatically mount new devices.

Whether to enable Systemd unit generator for zram devices.

Mount verity-protected block devices in the initrd

This option allows you to define Ethernet bridge devices that connect physical networks together

Whether to enable hid-fanatecff, a Linux kernel driver that aims to add support for Fanatec devices.

Extra command line options for the JVM running AirSonic

Packages providing extra SANE backends to enable.

Whether to enable access to video devices like cameras on the system .

Whether to enable RustDesk, a remote access and remote control software, allowing maintenance of computers and other devices.

Install the SPICE USB redirection helper with setuid privileges

Whether to enable joycond-cemuhook, a program to enable support for cemuhook's UDP protocol for joycond devices.

Whether to enable udev rules for devices supported by libjaylink

Whether to enable support for Logitech Wireless Devices.

Whether to enable udev rules and software for Flipper Zero devices.

Default block I/O scheduler